MTOMIX 4500 microsilica gel Clinic Beton Iran

MTOMIX 4500 microsilica gel, in addition to being used in making concrete with high strength, waterproofing, low permeability, high durability and special mortars, in concretes that reduce plastic cracks, improve the tensile and bending resistance of concrete. It is applicable. It is also recommended to use MTOMIX 4500 in situations where the concrete is subject to impact and intermittent dynamic loads. Microsilica gel is used in coastal concrete, waterproof and exposed to corrosive and destructive factors.

Types of microsilica gel

Types of microsilica gel are produced on two types of polycarboxylate and naphthalene base, which are as follows:

• SP1RB class microsilica gel
• APC5RRB class microsilica gel
• GEL-APC5RRC-N class microsilica gel
• Microsilis gel class GEL-APC5RRC-N-S-NEW
• Fiber microsilica gel Gel-ASP2RB
• Microsilica gel class Gel-ASP2AB
• ASP6RB grade micro silica gel
• FASP2RB class microsilica gel
• Colored microsilica gel

Applications of MTOMIX4500 microsilica gel:

The most important applications of microsilica gel are as follows:

• Coastal structures
• Water retaining structures
• Concrete pavements
• High strength concrete
• Structures exposed to dynamic loads, impact and fatigue
• Thin concrete sections
• Concrete structures exposed to extreme cycles of melting and freezing
• Military and defense concretes

Features of MTOMIX 4500 microsilica gel:

The most important features of microsilica gel are as follows:

1. Easy application and elimination of problems caused by direct use of microsilica powder
2. Reduced shipping cost compared to microsilica
3. Increased compressive strength
4. Reducing the ratio of water to cement
5. Reduced permeability
6. Increased durability due to increased electrical resistance and thus increased corrosion resistance
7. Increased durability due to reduced permeability

Amount of MTOMIX 4500 microsilica gel

The exact amount of microsilica gel MTOMIX4500 should be determined through workshop tests, so as a guide, it is recommended to add 5 to 8% of the weight of cement used to concrete. This amount can be added to concrete during or after construction. If microsilica gel is added in the truck mixer, it should be ensured that it is mixed in the concrete. For this purpose, between 3 and 5 minutes should be required after adding MTOMIX 4500 microsilica gel.

Side effects of using MTOMIX4500 microsilica gel outside the range

Side effects of microsilica gel; Consumption of less than 5% MTOMIX 4500 microsilica gel causes lack of proper quality and performance, rapid slump loss, reduction of free lime absorption power and relative lowering of all properties for concrete.
It is not recommended to use more than 8% of the cement weight of MTOMIX 4500 microsilica gel in concrete and it will be possible only by conducting workshop tests.

Appearance characteristics of MTOMIX4500 microsilica gel:

The appearance and technical specifications of microsilica gel are as follows:

• State: in a state of gelatinous stillness and after shaking the liquid
• Gray
• Specific weight: 1.35
• Chloride level: no chlorine or much less than the standard limit
• Nitrate: None
• Freezing point: zero degrees Celsius
• Flash point: None

The consumption of microsilica gel in concrete

The exact amount of microsilica gel consumption in concrete is determined through workshop tests. In general, 1 to 3 percent of the weight of cement used is added to concrete, which is added either during construction or after concrete construction. If it is added in the truck mixer, it should ensure the mixing of concrete, which should take 3 to 5 minutes after adding.

Physical and chemical characteristics of MTOMIX4500 microsilica gel

This product should not be mixed with any other material unless it is approved by the specialists of Concrete Clinic Iran.

Compositions and ingredients of microsilica gel

The components and ingredients of microsilica gel are as follows:

• Its main part is microsilica
• Concrete lubricant or super lubricant
• Polymer materials or concrete waterproofing
• Polypropylene fibers or steel fibers
• Antibacterial substances
• Water
• Special additives

How to store MTOMIX4500 microsilica gel

MTOMIX 4500 microsilica gel should be stored in its original container at a temperature of +5°C. If it freezes, you can heat it slowly and stir it to recycle again. Failure to observe proper storage conditions may damage the product or its container.

Purchase and price of MTOMIX4500 microsilica gel

Making the market is a database and a network of manufacturers and suppliers of construction products that introduces companies and specialized reviews of construction products. The general purpose of building a market is to establish a direct relationship between the buyer and the producer. Dear buyers, to know the price of microsilica gel, refer to the market system and buy MTOMIX4500 microsilica gel from reliable sellers.

Manufacturers and suppliers can register in the market construction system and participate in the special sales festival by placing construction products and inserting the suggested price and increase the sale of their products.