Market construction
Market construction
Market construction
Basic Materials
Concrete Additives
Concrete Sealer
Instant setting resin AQUAFIN-P1 Clinic Beton Iran

Instant setting resin AQUAFIN-P1 Clinic Beton Iran

Clinic Beton Iran
Iran

Instant resin AQUAFIN-P1 Iran concrete clinic:

AQUAFIN-P1 instant resin is resistant to acids and alkalis and is compatible with bituminous systems, as well as joint tapes.
You can also make a price as a seller
Request a price to negotiate and get a better offer

Suppliers

SuppliersExpiration datePrice (Toman)Minimum order (MOQ)CityPhone number
The price is not recorded

Instant setting resin AQUAFIN-P1 Clinic Beton Iran

AQUAFIN-P1 instant setting resin is a highly active one-component modified isocyanate that is ready to use without the need for a stirrer. This product has a strong increase in viscosity in the vicinity of water and creates a strong viscoelastic foam that will temporarily prevent the penetration, leakage and flow of water. AQUAFIN-P1 instant resin is resistant to acids and alkalis and is compatible with bituminous systems, as well as joint tapes. On completely dry surfaces, the material forms foam immediately, but hardens slowly with moisture in the soil. Expandable injection resin based on polyurethane, single component and injectable in seams and cracks containing water.

AQUAFIN-P1 instant setting resin in the form of one-component polyurethane

Method of using AQUAFIN-P1 instant resin

It is used to inject and seal concrete and stone cracks and joints.

In general, AQUAFIN-P1 instant resin is used for two purposes:

Preventing the flow and leakage of water from cracks and seams

Keeping loose gravel stable

This product has been prepared according to the approval of DFBT (Evaluation of the effect of executive products on concrete and underground water) in November 2000.

Surrounding surfaces that are not going to be protected by AQUAFIN-P1 materials should be covered and the materials should be prevented from coming into contact with those areas.
AQUAFIN-P1 instant setting resin is not physiologically harmful after hardening.

AQUAFIN-P1 instant resin coating surface

The use of this product is not limited to the cases mentioned in this sheet and it can be used in similar cases according to the consultant's opinion.
In general, all the general protection laws of coatings have been observed for this product.

AQUAFIN-P1 instant resin consumption amount

AQUAFIN-P1 instant resin reacts with air and water moisture. Therefore, there will be a possibility of forming a crust-like layer on the surface of the liquid in open containers, which will not be affected by the injection process.

In general, materials are injected by injection nozzles or hand pumps in areas where there is water. AQUAFIN-P1 instant resin forms foam and hardens in the vicinity of water. Therefore, if the amount of water in the area to be sealed is low, some water is injected to carry out the reactions.

The application is performed according to the injection instructions in Turk (ZTV_riss or Rili from Dafstb).

Performance of AQUAFIN-P1 instant setting resin

It is suggested to store the materials before use for at least 12 hours at a temperature of more than 15 degrees Celsius so that the materials are within the temperature range of applying the two processes between 15 degrees Celsius and 30 degrees Celsius.

1. Concrete cracks (with a width of about 0.2 mm) should be drained to a depth of 20 cm.

2. Drained areas should be cleaned with clean air pressure.

3. The injection pumps should be installed in the right place.

4. Inject AQUAFIN-P1 instant resin with a suitable device. For vertical cracks, start the injection from the bottom and for horizontal cracks from the left side. The amount of material consumption is about 1150 g/I.

5. If necessary, before the AQUAFIN-P1 instant resin is completely hardened, the injection device should be moved away from the place and leveled on the crack by ASOCORET-RN.

Protection and safety of AQUAFIN-P1 instant resin

Tools and equipment must be thoroughly cleaned with ASO-R006 cleaner before use. After finishing work or in cases where there is a lot of downtime, the injection machine must be cleaned so that the material does not dry out in the machine. The cleaning solution must have an evaporation temperature of more than 21 degrees Celsius.

The rest of the injection material should be removed from the injection tool by pressure, and the injection tool and the tube should be washed with a rotating current for 5-10 minutes, empty its contents and wash again with clean ASO-R006.

During the time when injection tools are going to be unused for a long time, it is better to fill them with ASO-R006 solvent during this time.

Purchase and price of instant resin AQUAFIN-P1 at Concrete Clinic Iran

Making the market is a database and a network of manufacturers and suppliers of construction products that introduces companies and specialized reviews of construction products. The general purpose of building a market is to establish a direct relationship between the buyer and the producer. Dear buyers, to know the price of concrete waterproofing, refer to the market system and buy AQUAFIN-P1 instant resin from reliable sellers.

Manufacturers and suppliers can register in the market construction system and participate in the special sales festival by placing construction products and inserting the suggested price and increase the sale of their products.

User's comments and scores