AQUAFIN-2K-M elastomeric waterproofing mortar Clinic Beton Iran

AQUAFIN_2K/M elastomeric sealing mortar is a two-component elastomeric compound, flexible and modified with polymer, which is used to protect and seal concrete, cement, brick and some natural stone surfaces due to its ability to bridge cracks. . Flexible two-component cement-based elastomeric waterproofing mortar, modified with polymer.

Properties and effects of AQUAFIN-2K-M elastomeric waterproofing mortar

1. Can be applied on wet surfaces without the need for primer

2. Easy implementation by brush, roller, spray and trowel

3. The ability to bridge cracks up to 1.6 mm wide

4. Not creating an obstacle against the exit of water vapor, (Vapor barrier coating is not.)

5. Resistant to abrasion, mechanical wear, UV and de-icing salts.

6. With DVGW W347 drinking water approval

7. Resistant against water attacking concrete according to DIN 4030 standard

8. Elongation under stretching more than 80%

9. It can be used as a coating and can also be covered (overcoating) with hard or flexible mortars and other types of colors and coatings.

Applications of elastomeric waterproofing mortar AQUAFIN-2K-M

For sealing water structures, sewage plants, external surfaces of underground walls, retaining walls, sealing swimming pools, water features, aquariums, artificial lakes, waterways, wet surfaces, surfaces under tiling, roofs Soldiers, expansion and execution seams along with ASO-JOINT-TAPE seam reinforcement tape

General sealing:

- External sealing of new and old buildings against moisture, soil moisture and water pressure

- Sealing of masonry walls by creating a horizontal cement barrier

- Internal sealing against the humidity of the external environment

- Sealing underground parking lots, prefabricated garages, containers, water sources, agricultural water storage tanks, water channels, surfaces exposed to high humidity, terraces, balconies and swimming pools.

- In order to keep ASO-JOINT-TAPE seam reinforcement tapes fixed

Sealing the surface under the tile:

- AQUAFIN-2K-M elastomeric waterproofing mortar is suitable and economical for sealing the surface under tiles in rooms exposed to moisture, where long resistance against water penetration is considered, such as bathrooms, kitchens and balconies. be Also, sealing the inner surface of swimming pools is one of the main uses of this product.

Attention:

If there is negative pressure, it is better to apply a layer of AQUAFIN_1K as a primer first.

AQUAFIN-2K-M elastomeric waterproofing mortar can be presented in various colors and designs, and it can also be painted.

The minimum thickness of the dried and hardened film at any point of coverage of these figures is the technical values of the product and does not reflect your actual needs. Please refer to the building codes for the minimum thickness of the film layer. On the uneven surface, more materials should be used to reach the recommended minimum thickness.

Method of using AQUAFIN-2K-M elastomeric waterproofing mortar

The desired surface must be completely cleaned and all surface contamination such as grease must be removed with a suitable cleaner, dust particles and protrusions must be removed from the surface.

AQUAFIN-2K-M elastomeric waterproofing mortar is suitable for soft cement surfaces, cement ingots, asphalt mortar, cement plaster, plaster and cement walls.

All holes and depressions in concrete blocks should be filled and repaired with suitable cement mortar, ASOCRET-FS and AQUAFIN.

To increase the adhesion between the coating and the surface, it is better to coat surfaces that are highly absorbent, such as plaster shavings and light concrete, with ASO-unigrund primer.

In order to prepare the surface, depending on the conditions, suitable methods such as sweeping, vacuuming, surface grinding, milling, shot blasting or water jet can be used.

details:

It is better to use ASOCRET-RN or ASOPLAST-MZ mortar at the junction of the wall with the floor and the concave corners of cm4.

External cracks can be sealed with AQUAFIN-2K-M elastomeric sealing mortar and ASO-JOINT-TAPE-2000 tape.

ASO-JOINT-TAPE-2000-S should be used for mobile cracks and executive seams.

Mixing:

The ingredients should be added with a volume ratio of 5 parts powder to 3 parts liquid. For this purpose, first pour 2/3 of the liquid component (UNIFLEX-M) into a clean bucket, while mixing, add AQUAFIN_2K/M powder to it and continue stirring until a uniform and soft mixture is reached.

Attention:

Depending on the use, to adjust the concentration during application, a maximum of 1.5% of water can be added to the ingredients while stirring.

Performance of AQUAFIN-2K-M elastomeric waterproofing mortar

The surface must be wet throughout the material. AQUAFIN-2K/M can be applied by brush, roller, trowel and even spray. Finally, applying 2 layers of coating is necessary to achieve the required thickness to reach the desired conditions. The second layer should be applied with a time interval of 4 hours from the application of the first layer and until the first layer is not damaged.

To avoid cracking of the coating after drying, the thickness of AQUAFIN-2K/M should not exceed 1 mm in each layer.

ASO-SYSTEM FLEECE-02 can be used in the second layer to strengthen the AQUAFIN-2K/M film.

Important recommendations:

In hot and humid areas, the coating may become sticky during curing. If this happens, mist the cover with water for 24 hours to ensure the complete hydration process.

Negative water pressure during freezing conditions can damage the coating.

AQUAFIN-2K-M elastomeric waterproofing mortar can be covered with a variety of solvent-free paints, coatings and other flexible mortars.

On surfaces with high humidity, for example, in water tanks, you should wait until the necessary time has passed for the surface to dry completely.

The coating should be protected from direct sunlight during application.

The surface to be applied must first be sufficiently wet.

The surfaces on which AQUAFIN-2K-M elastomeric waterproofing mortar is not to be applied must be covered and protected.

When directly contacting metals such as copper, zinc and aluminum with tight holes, ASODUR-GBM primer should be used in two layers. The first layer should be applied on the clean surface with a brush and carefully after a short period of time (about 3 to 6 hours), when the first layer has dried enough, and then on the surface of the corroded quartz primer (with a particle size of 7/mm) 0 to 0.2) to be played. The consumption amount of ASODUR-GBM is approximately 800-1000 g/m2. In order to seal PVC and steel flanges, first the desired surface should be rubbed and then washed with isopropanol or acetone, and then AQUAFIN-2K-M materials with ASO-JOINT-SLEEVE tape or ADF-Pipe without bubbles be applied The powder component of AQUAFIN-2K-M elastomeric waterproofing mortar is classified in the category of stimulants.

Purchase and price of elastomeric waterproofing mortar AQUAFIN-2K-M at Iran Concrete Clinic

Making the market is a database and a network of manufacturers and suppliers of construction products that introduces companies and specialized reviews of construction products. The general purpose of building a market is to establish a direct relationship between the buyer and the producer. Dear buyers, to know the price of concrete waterproofing, they can refer to the market construction system and order to buy AQUAFIN-2K-M elastomeric waterproofing mortar from Iran Concrete Clinic from reliable sellers.

Manufacturers and suppliers can register in the market construction system and participate in the special sales festival by placing construction products and inserting the suggested price and increase the sale of their products.